Dispensing machine daily maintenance steps
2019/2/27
Dispensing machine in the production of industrial use range is very wide, many industries are applied to point glue craft, such as filling, integrated circuits, semiconductor packaging, at the bottom of the article element coating, lamp, etc., but in use process, we must pay attention to the dispensing equipment maintenance maintenance, otherwise will appear for equipment use fixed number of year is too long the various problems of the machine.
The following method for dispensing machine maintenance:
Methods/procedures
1, equipment cleaning and maintenance as a whole
A check, whether the equipment the motion mechanism of screw loose phenomenon, including the X, Y, Z, rail transportation, adjustable width architecture.
B, the waste of glue inside the empty cup, operation platform, and clean.
C, on a regular basis to the X, Y, Z amplitude modulation of screw and slide to clean preview.
D, check the cooling fan is working correctly, circuit loss and loose ends.
E, regularly check the moisture release of pressure filters and check the air compressor is normal.
2, the maintenance of the valve body
Equipment at the stop line want to clean or replace the different types of glue dispensing valve, otherwise easily lead to cavity glue is difficult to clean, firing pin set inside the chamber and nozzle clogging and so on.
How to maintain?
First close the injection valve and remove the plastic bucket - over plastic barrels - open the injection valve - the guide lines and cavity residual rubber - closed injection after pour a little wine in the empty plastic barrels
Fine - open the injection valve - row clean alcohol - nozzle cavity/guide/hose will be removed - ten minutes into the ultrasonic vibrations with alcohol - scrub with the brush off the remaining residue after removal lon-izing air dry
Net to reassemble injection valve - installed back to the device.
Note:
A, more than 8 hours downtime is not production, suggested that the injection valve for cleaning and maintenance, to prevent the nozzle blocking.
B, do not use more than use time of glue, or it will influence on the performance of the glue used.
C, washing the firing pin seal to avoid using xylene, acetone, and corrosive solvent clean or soak, otherwise you will make the sealing ring damaged by corrosion lead to deformation.
Correct maintenance to use lifespan and glue dispensing stability has important relation, please be sure to pay attention to, by using the maintenance cycle, can reduce equipment failures,
Improve efficiency, and at the same time so that we can improve the service life of the equipment. Above is for the "correct maintenance method of glue" part of the related introduction, so to be executed in accordance with the above points at ordinary times,
So in the process of daily use can reduce some unnecessary problems, help us to finish the work faster.
The following method for dispensing machine maintenance:
Methods/procedures
1, equipment cleaning and maintenance as a whole
A check, whether the equipment the motion mechanism of screw loose phenomenon, including the X, Y, Z, rail transportation, adjustable width architecture.
B, the waste of glue inside the empty cup, operation platform, and clean.
C, on a regular basis to the X, Y, Z amplitude modulation of screw and slide to clean preview.
D, check the cooling fan is working correctly, circuit loss and loose ends.
E, regularly check the moisture release of pressure filters and check the air compressor is normal.
2, the maintenance of the valve body
Equipment at the stop line want to clean or replace the different types of glue dispensing valve, otherwise easily lead to cavity glue is difficult to clean, firing pin set inside the chamber and nozzle clogging and so on.
How to maintain?
First close the injection valve and remove the plastic bucket - over plastic barrels - open the injection valve - the guide lines and cavity residual rubber - closed injection after pour a little wine in the empty plastic barrels
Fine - open the injection valve - row clean alcohol - nozzle cavity/guide/hose will be removed - ten minutes into the ultrasonic vibrations with alcohol - scrub with the brush off the remaining residue after removal lon-izing air dry
Net to reassemble injection valve - installed back to the device.
Note:
A, more than 8 hours downtime is not production, suggested that the injection valve for cleaning and maintenance, to prevent the nozzle blocking.
B, do not use more than use time of glue, or it will influence on the performance of the glue used.
C, washing the firing pin seal to avoid using xylene, acetone, and corrosive solvent clean or soak, otherwise you will make the sealing ring damaged by corrosion lead to deformation.
Correct maintenance to use lifespan and glue dispensing stability has important relation, please be sure to pay attention to, by using the maintenance cycle, can reduce equipment failures,
Improve efficiency, and at the same time so that we can improve the service life of the equipment. Above is for the "correct maintenance method of glue" part of the related introduction, so to be executed in accordance with the above points at ordinary times,
So in the process of daily use can reduce some unnecessary problems, help us to finish the work faster.
